返回首页

北京公路护栏网厂

本站导航

新闻动态

当前位置:网站首页 > 新闻动态 > 详细信息
公路护栏网通常使用
添加时间:2022/12/21 15:51:23     浏览次数:
公路护栏网通常使用的防腐方式为粉末浸塑法,它起源于流化床法,所谓的流化床最初是在温克勒气体发生炉上应用于石油接触分解,进而开发了固气两相接触工艺,后逐渐用于金属涂塑方面。所以有时仍叫“流化床包覆法”,实际过程是把粉末涂料加入底部多孔透气的容器(流动槽)中,由鼓风机从下送入经过处理的压缩空气,使粉末涂料翻动达到“流化状态”,成为均匀分布的细散粉末。
Anticorrosion of highway fence is usually used for powder impregnation method, which originated in the fluidized bed method, the fluidized bed was originally in the Winkler gas generating furnace used in petroleum and contact decomposition, developed a solid gas two-phase contact process, after gradually for the metal coated hand. I sometimes called the fluidized bed coating method, the actual process is put into a container at the bottom of the powder coating porous breathable (flow), by the blower from processed into compressed air, make the powder coating reach "fluidized state", become the uniform distribution of fine powder.
公路护栏网的涂装工艺由两个阶段来完成:第一阶段为固定床阶段,第二阶段为气流输送阶段,在固定床的基础上继续增大流速(W),床层开始膨胀和松动,床层高度开始增加,每个粉末颗粒被浮起,因而离开原来位置作一定程度的移动,这时便进入流化床阶段。bc段说明流化床内粉层膨胀,其高度(I)随着气体速度的增大而增加,但床内压强(△P)并不增大,在一定范围内变动流速而不影响流体所需的单位功率,这是流化床的特征,正是利用这一特点来进行涂装工艺实施的。流化床内粉末流化状态的均匀性是保证涂膜均匀的关键。在粉末涂装上用的流化床属于“竖式流态化”,流化数必需经过试验找出,一般以能够涂敷即可,流化床内粉末的悬浮率最高可达型槽模具 井盖钢模具 保定雅思 一次性止血带 保定养老院  保定水处理设备 一次性止血带  30~50%。
Coating process of highway guardrail is accomplished by two stages: the first stage is a fixed bed stage, the second stage is the stage of air transportation, continue to increase the flow rate based on fixed bed (W), the bed began to swell and loose, the height of bed began to increase, each powder particles float, thus leaving the original position move to a certain extent, it will enter the stage of fluidized bed. BC shows that fluidized bed powder layer expansion, its height (I) increased with increasing gas velocity, but the bed pressure (P) does not increase, changes in flow rate in a certain range without affecting the unit power fluid required, the fluidized bed features, is to use the implementation of coating process a special point. The uniformity of fluidization in fluidized bed is the key to ensure the uniformity of film. The powder coating used in fluidized bed belong to the vertical fluidization, the flow number must be found in the test, in general, can be suspended in the fluidized bed can be coated, powder rate of up to 30 ~ 50%.
上一页  没有了  
下一页  机场防护网特点
  • 关于我们
  • 新闻动态
  • 案例展示
  • 网上订单
  • 联系我们
  • 产品分类1
  • 产品分类2
  • 产品分类3

Copyright © 技术支持:遨游网络

  • 联系我们
  • 网上订单
  • 工程案例
  • 本站导航

搜索

  • 关于我们
  • 新闻动态
  • 案例展示
  • 网上订单
  • 联系我们
  • 产品分类1
  • 产品分类2
  • 产品分类3